Pickup from our Mississauga warehouse · 5250 Satellite Drive, Unit 7 905-617-0298Cut Sheet LibraryCustomer Portal (Coming Soon)
Home / Products / Accessories / Single Colour Accessories / DC Splitter · 5-Way
DC Splitter · 5-Way Single Colour Accessories
Single Colour Accessories

DC Splitter · 5-Way

SL-SPL-5W

1 × DC jack input, 5 × DC plug outputs.

Connection1 × DC jack input, 5 × DC plug outputs
Cut Sheet (PDF)
How It Works

One Adaptor, Five Runs of Light

The SL-SPL-5W turns one DC power source into 5 separate outputs, so a single plug-in adaptor can light 5 lengths of LED strip or COB tape: under-cabinet runs, shelves, coves or displays that are cut and installed separately. The adaptor’s DC plug goes into the splitter’s DC jack, and each of the 5 DC plugs connects to a run fitted with a DC female lead. No splicing at the outlet, and each run can be unplugged on its own.

5-WAY SPLITTER · ONE ADAPTOR, 5 RUNSOne plug-in adaptor feeds the splitter; each output powers its own length of LED strip or COB tape.DC12V or 24VPLUG-IN ADAPTORPS · 12V or 24V models1 → 5SPLITTERSL-SPL-5WTHIS PARTDC FEMALE LEADNL-DCFEMALE-2MLED STRIP OR COB TAPEcut to length
5-way set-up. Plug-in adaptor → SL-SPL-5W → a DC female lead (NL-DCFEMALE-2M) soldered to each run.
1 → 5Outputs
DC jackInput
5 × DC plugOutputs
Strip + COBSingle colour tape
The Installation Process

Where the Splitter Fits

The splitter sits between the power and the strip. Add an extension before or after it when a run needs more reach.

WHERE THIS PART FITS1 · POWERPlug-in adaptoror hard-wired driver+ NL-DCMALE-2M2 · EXTENDSL-EX-1M / 2Moptional · adds reach3 · SPLITSL-SPL-2W / 3W / 5Woptional · 2, 3 or 5 runs4 · CONNECTNL-DCFEMALE-2Msoldered to the strip5 · LIGHTLED strip or COB tapecut to length
Plug-in installation order: power → extend → split → connect → light.
EXTENSION + SPLITTER · DIFFERENT DISTANCES FROM ONE ADAPTORUse an extension on any splitter output that needs to reach a run further away.DC12V or 24VPLUG-IN ADAPTORPS · 12V or 24V models1 → 2SPLITTERSL-SPL-2WSL-EX-1M / 2MNEAR RUNFAR RUNDC FEMALE LEADNL-DCFEMALE-2MLED STRIP OR COB TAPE
Different distances. A DC extension cable on one output reaches a run further away.
Installation

Five Steps

  1. Plan the runs. Cut each length of strip or COB tape at its marked cut points. One splitter output per run, up to 5.
  2. Check the load. Add up the wattage of all runs; the total must stay within one adaptor’s rating, with about 20% headroom.
  3. Fit a DC lead to each run. Solder an NL-DCFEMALE-2M lead to the + and − pads at the end of each run. Prefer not to solder? Fit a tape-to-wire lead or COB strip-to-wire splice to the strip and join its wires to the DC lead with an H-connector. Check your tape’s Compatible Accessories for the right width.
  4. Connect. Plug each run onto a splitter output, then plug the adaptor into the splitter’s DC jack. Add an SL-EX extension wherever a lead needs to reach further.
  5. Power up and test. Plug the adaptor into the outlet and check every run lights evenly.
Important Notes
  • One power source: the splitter shares the adaptor’s power between the runs; it does not add any.
  • Match the voltage: use 24V tape with a 24V adaptor or driver, and 12V tape with 12V.
  • Polarity: always + to + and − to − when soldering or joining wires. The DC plugs only fit one way.
  • Size the power: add up the wattage of every run (W/m × metres) and choose an adaptor or driver with about 20% headroom.
  • Hard-wired driver? Fit an NL-DCMALE-2M lead to its DC output and the splitter plugs in the same way.
Example: five 1.5 m runs of 320 Super Slim COB at 8 W/m = 60 W. A 96 W 24V plug-in adaptor (about 77 W with 20% headroom) powers all five through one SL-SPL-5W.
Quick Guide

Parts for This Set-Up

Part What It Does Part Number
Plug-In Adaptor Plugs into a standard outlet; DC plug output. 12V: 12, 36 or 60 W. 24V: 36, 60 or 96 W. PS-…-12V / 24V
DC Splitter · 5-Way 1 × DC jack input, 5 × DC plug outputs. SL-SPL-5W
DC Extension Cable Male / female extension, 1 m (3’3″) or 2 m (6’6″). SL-EX-1M / SL-EX-2M
DC Lead · 2 m (female) Soldered to the strip; accepts the DC plug from a splitter, extension or adaptor. NL-DCFEMALE-2M
Tape-to-Wire Lead / COB Splice No-solder option: connects a cut end of tape to bare wires. Match the tape width. DT-100CM-8/10 · DT-SPLICE-8-COB-P
H-Connector Wire Splice Joins two ends of low-voltage wire (+ and −). DT-H-CONN

Need more or fewer outputs? See the 2-way · 3-way splitter.

Specifications

Type
DC splitter
Connection
1 × DC jack input, 5 × DC plug outputs

 

Works with
300 Series, 300 Series Bendable, 600 Series, 800 Series, 160 Series COB, 320 Series COB, 320 Super Slim COB (5 mm), 320 COB 8 m IP67, 480 Series COB, 2835 Sauna & Steam, 2216 Sauna & Steam

Specifications from the DayTech LED cut sheet. Subject to change without notice.

Planning a Project with the DC Splitter · 5-Way?

Tell us the lengths and layout and we'll quote the tape, channel, connectors and driver for each run.