Pickup from our Mississauga warehouse · 5250 Satellite Drive, Unit 7 905-617-0298Cut Sheet LibraryCustomer Portal (Coming Soon)
Home / Products / Accessories / Single Colour Accessories / DC Lead · 2 m
DC Lead · 2 m Single Colour Accessories
Single Colour Accessories

DC Lead · 2 m

NL-DCMALE-2M, NL-DCFEMALE-2M

2 m (6'6") DC male or DC female lead to connect to a hard-wired power supply.

ConnectionDC male or DC female to hard-wired power supply
Lead length2 m
Type
Your Part NumberNL-DCMALE-2M, NL-DCFEMALE-2M
Pairs With the DC Plug Male Connector

Screw-terminal male DC plug (DC-PLUG-MALE) that turns bare low-voltage wire into a plug-in DC connection.

DC Plug Male ConnectorDC-PLUG-MALEView DC Plug Male Connector
Pairs With the DC Plug Female Connector

Screw-terminal female DC plug (DC-PLUG-FEMALE) that turns bare low-voltage wire into a plug-in DC connection.

DC Plug Female ConnectorDC-PLUG-FEMALEView DC Plug Female Connector
Cut Sheet (PDF)
How It Works

Two Ways to Use the DC Lead

The 2 m (6’6″) DC lead is the link between bare-wire LED strip and DayTech’s plug-in DC accessories. One end has a DC connector, the other end two bare wires. The female lead (NL-DCFEMALE-2M) is soldered to the end of a length of LED strip or COB tape, so the strip can plug into a plug-in adaptor, splitter or extension. The male lead (NL-DCMALE-2M) connects to a hard-wired power supply, so the same plug-in accessories can run from a hard-wired driver.

DC LEAD · SOLDERED TO THE STRIPSolder the lead’s two wires to the + and − pads at the end of the strip, then plug the strip in.DC12V or 24VPLUG-IN ADAPTORPS · 12V or 24V models→DC FEMALE LEADNL-DCFEMALE-2M (2 m)THIS PART+−+−STRIP END · SOLDER PADSmatch + to + and − to −
Female lead on the strip. Solder the two wires to the + and − pads at the end of the strip; the strip then plugs into any DC plug.
DC MALE LEAD · HARD-WIRED DRIVER TO PLUG-IN ACCESSORIESFit the male lead to a hard-wired driver’s DC output; then the splitters and extensions plug straight in.AC120 VAChard-wiredDRIVER12V or 24V DCHARD-WIRED DRIVERDC MALE LEADNL-DCMALE-2MTHIS PART1 → 2SPLITTERSL-SPL-2WDC FEMALE LEADNL-DCFEMALE-2MLED STRIP OR COB TAPE
Male lead on a hard-wired driver. The driver’s DC output gets a plug, so splitters and extensions plug straight in.
The Installation Process

Where the DC Lead Fits

WHERE THIS PART FITS1 · POWERPlug-in adaptoror hard-wired driver+ NL-DCMALE-2M2 · EXTENDSL-EX-1M / 2Moptional · adds reach3 · SPLITSL-SPL-2W / 3W / 5Woptional · 2, 3 or 5 runs4 · CONNECTNL-DCFEMALE-2Msoldered to the strip5 · LIGHTLED strip or COB tapecut to length
Plug-in installation order: power → extend → split → connect → light. The male lead belongs at step 1 with a hard-wired driver.
Soldering

Soldering the Lead to the Strip

  1. Cut the strip. Cut only on the marked cut line so a full set of + and − pads is exposed.
  2. Prepare. Strip a few millimetres of insulation from each wire and tin the wires and the two pads with solder.
  3. Solder. Join the + wire to the + pad and the − wire to the − pad. Keep the joints clean with no solder bridging the pads.
  4. Insulate and secure. Cover the joints with heat-shrink and support the lead so the joint isn’t carrying the cable’s weight.
  5. Test. Plug in the adaptor (or splitter output) before installing the strip in its channel.
Important Notes
  • Match the voltage: use 24V tape with a 24V adaptor or driver, and 12V tape with 12V.
  • Polarity: always + to + and − to − when soldering or joining wires. The DC plugs only fit one way.
  • Size the power: add up the wattage of every run (W/m × metres) and choose an adaptor or driver with about 20% headroom.
  • No soldering iron? Fit a tape-to-wire lead or COB strip-to-wire splice to the strip and join its wires to the DC lead with an H-connector. Check your tape’s Compatible Accessories for the right width.
Quick Guide

Male or Female?

You Want to Connect How Part Number
A strip that plugs into an adaptor, splitter or extension Solder to the strip NL-DCFEMALE-2M
A hard-wired driver feeding splitters, extensions or strips Connect to the driver’s DC output NL-DCMALE-2M
A strip that plugs into a hard-wired driver fitted with a female lead Solder to the strip NL-DCMALE-2M
Weatherproof neon (outdoor) DC male to bare wires, IP67; also 15 cm NL-DCMALE-2M-IP67
Works With

Plug-In Accessories

Part What It Does Part Number
Plug-In Adaptor Plugs into a standard outlet; DC plug output. 12V: 12, 36 or 60 W. 24V: 36, 60 or 96 W. PS-…-12V / 24V
DC Extension Cable Male / female extension, 1 m (3’3″) or 2 m (6’6″). SL-EX-1M / SL-EX-2M
DC Splitter · 2-Way 1 × DC jack input, 2 × DC plug outputs. SL-SPL-2W
DC Splitter · 3-Way 1 × DC jack input, 3 × DC plug outputs. SL-SPL-3W
DC Splitter · 5-Way 1 × DC jack input, 5 × DC plug outputs. SL-SPL-5W
H-Connector Wire Splice Joins two ends of low-voltage wire (+ and −). DT-H-CONN

Specifications

Type
DC lead
Lead length
2 m (6'6")
Connection
DC male or DC female to hard-wired power supply

 

Key details
For DC cables and splitters on RGB systems, use the single colour guide too
Works with
300 Series, 300 Series Bendable, 600 Series, 800 Series, 160 Series COB, 320 Series COB, 320 Super Slim COB (5 mm), 320 COB 8 m IP67, 480 Series COB, 2835 Sauna & Steam, 2216 Sauna & Steam

Specifications from the DayTech LED cut sheet. Subject to change without notice.

Planning a Project with the DC Lead · 2 m?

Tell us the lengths and layout and we'll quote the tape, channel, connectors and driver for each run.