Single Colour Accessories DC Splitter · 5-Way
SL-SPL-5W
1 × DC jack input, 5 × DC plug outputs.
One Adaptor, Five Runs of Light
The SL-SPL-5W turns one DC power source into 5 separate outputs, so a single plug-in adaptor can light 5 lengths of LED strip or COB tape: under-cabinet runs, shelves, coves or displays that are cut and installed separately. The adaptor’s DC plug goes into the splitter’s DC jack, and each of the 5 DC plugs connects to a run fitted with a DC female lead. No splicing at the outlet, and each run can be unplugged on its own.
Where the Splitter Fits
The splitter sits between the power and the strip. Add an extension before or after it when a run needs more reach.
Five Steps
- Plan the runs. Cut each length of strip or COB tape at its marked cut points. One splitter output per run, up to 5.
- Check the load. Add up the wattage of all runs; the total must stay within one adaptor’s rating, with about 20% headroom.
- Fit a DC lead to each run. Solder an NL-DCFEMALE-2M lead to the + and − pads at the end of each run. Prefer not to solder? Fit a tape-to-wire lead or COB strip-to-wire splice to the strip and join its wires to the DC lead with an H-connector. Check your tape’s Compatible Accessories for the right width.
- Connect. Plug each run onto a splitter output, then plug the adaptor into the splitter’s DC jack. Add an SL-EX extension wherever a lead needs to reach further.
- Power up and test. Plug the adaptor into the outlet and check every run lights evenly.
- One power source: the splitter shares the adaptor’s power between the runs; it does not add any.
- Match the voltage: use 24V tape with a 24V adaptor or driver, and 12V tape with 12V.
- Polarity: always + to + and − to − when soldering or joining wires. The DC plugs only fit one way.
- Size the power: add up the wattage of every run (W/m × metres) and choose an adaptor or driver with about 20% headroom.
- Hard-wired driver? Fit an NL-DCMALE-2M lead to its DC output and the splitter plugs in the same way.
Parts for This Set-Up
| Part | What It Does | Part Number |
|---|---|---|
| Plug-In Adaptor | Plugs into a standard outlet; DC plug output. 12V: 12, 36 or 60 W. 24V: 36, 60 or 96 W. | PS-…-12V / 24V |
| DC Splitter · 5-Way | 1 × DC jack input, 5 × DC plug outputs. | SL-SPL-5W |
| DC Extension Cable | Male / female extension, 1 m (3’3″) or 2 m (6’6″). | SL-EX-1M / SL-EX-2M |
| DC Lead · 2 m (female) | Soldered to the strip; accepts the DC plug from a splitter, extension or adaptor. | NL-DCFEMALE-2M |
| Tape-to-Wire Lead / COB Splice | No-solder option: connects a cut end of tape to bare wires. Match the tape width. | DT-100CM-8/10 · DT-SPLICE-8-COB-P |
| H-Connector Wire Splice | Joins two ends of low-voltage wire (+ and −). | DT-H-CONN |
Specifications
Specifications from the DayTech LED cut sheet. Subject to change without notice.
| Part Number | Voltage | IP Rating | Colour | Length / Size | Power | Quote |
|---|---|---|---|---|---|---|
| SL-SPL-5W | 5-way |
Works with These Products
300 Series LED StripSL-SPL-5W
300 Series Bendable LED TapeSL-SPL-5W
600 Series LED StripSL-SPL-5W
800 Series LED TapeSL-SPL-5W
160 Series COB TapeSL-SPL-5W
320 Series COB TapeSL-SPL-5W
320 Super Slim COB Tape (5 mm)SL-SPL-5W
320 Series COB Tape (8 m, IP67)SL-SPL-5W
480 Series COB TapeSL-SPL-5W
2835 Sauna & Steam LED TapeSL-SPL-5W
2216 Sauna & Steam Tape LightSL-SPL-5W
Planning a Project with the DC Splitter · 5-Way?
Tell us the lengths and layout and we'll quote the tape, channel, connectors and driver for each run.




